Solar Products, Inc. is America's leading supplier of premium electric infrared heaters. Backed by over 60 years of innovation in manufacturing infrared heating solutions, all of our products are guaranteed to deliver efficient heating performance with unbeatable reliability. We are proud of introducing Solar products in East Asia market. Should you have any inquiry please contact us sales@cmteastasia.com or ring the office.
The quartz tubing can be constructed as either clear or translucent, and the tube’s coils can be produced as standard or fast response. Their terminations are manufactured as flag type, stud type, wire leads, wire terminal, quick disconnect, fuse type or single-ended type. Our quartz tubes are available with no reflector, an internal ceramic reflector or a gold-backed reflector. The tubes’ watt density can be done up to 60 watts/lineal inch, and the tubes have a maximum length of 90″. They can be pre-assembled into a fixture or purchased individually.
Optional Back-mounted fans
Fast heatup and cooldown time. Air holes between elements for cooling/scrubbing.
Optional Pyrometer view port through heater.
Optional Parallelogram modules for zoning across wide webs.
The unique V-shaped element provides numerous performance improvements over conventional stamped element heaters including the following:
Reduced cost
Faster heat-up and cool-down
Higher watt density
Reduced thermal back-losses
More robust construction (no need for special handling or shipping)
More freely radiating design
Longer life
Elimination of hot spots
Improved heating uniformity
Element temperatures up to 2,100° F (2 micron peak wavelength)
Typical life expectancy of 12,000+ hours, depending on temperature
Heater wattages up to 100 watts per square inch
Can be operated in any plane without any element sag or “coil creep”
Stainless steel screen protects face
Maintenance free
Various voltages up to 600V
Superior mechanical strength
¹/4 -20 mounting studs
Electrical junction box
Replaceable type K thermocouple
Air holes for extremely fast cool down and/or to provide scrubbing action in drying applications
Pre-mounted fans
Multi-zone heaters
Pyrometer view port through heater
Stainless steel housing
No housing (heater board only)
Wire leads
Offers power densities and response time that rival short wavelength heaters.
Fast-responding, medium-wavelength, infrared panel heaters using stamped serpentine elements have been used in industry for decades. In traditional construction, the flat elements are held against a refractory board by manually inserted pins. Solar Products Inc. has developed a unique V-shaped element which provides numerous performance improvements over conventional stamped element heaters including the following:
Reduced thermal back-losses
Higher watt density
More robust construction
More freely radiating design
Longer life
Elimination of hot spots
Improved heating uniformity
Lower cost
According to Paul Ross, VP of Product Development “…Solar Products didn’t invent the stamped element heater, but we certainly perfected it…”
Recently, Solar Products pitted their V Series heater against the competition in a head-to-head comparison.
Solar Products built a V series heater to closely match a sample heater from a leading competitor. Both heaters were 4.25” x 13.75” with (2) elements of 11” heated length. The competition used 0.135” thick elements and Solar used its closest match, 0.139” thick. To compensate for the slight difference in resistance, the voltage was adjusted so that each heater produced the same total wattage of 1,481W
Back side of heaters during test.
V-series on left. pinned elements on right.
With both heaters operating at the same wattage for the same period of time, a thermal imaging camera from Electrophysics was used to capture an image of the back side of the heaters.
Thermal image of back side of heaters.
V series on left. Conventional pinned element on right.
In thermal imaging, the hottest temperature is represented by the brightest color. The images clearly show how much more heat is lost to the back side of the heater via conduction along the numerous element-retaining pins.
Close-up of pinned element.
The elimination of heat-conducting pins is one giant step in reducing back losses. Another giant step is the use of 2” of insulation behind the board, which is standard construction for the Solar Products V Series heaters and is not even offered by the competition. The combination of these two factors gives the V series greatly reduced back losses and therefore, increased radiant efficiency.
The numerous mounting pins in conventional stamped element heaters perforate the refractory and significantly weaken it to the point that when shipped in a horizontal plane, the heater frequently breaks under its own weight. For this reason, it is common for OEMs to remove heaters from a machine to be packed and shipped separately and then to be re-installed on site. This additional handling can be costly.
The bonded V-shaped element actually increases the board strength. The cement in the mounting grooves has been found to penetrate into the board, bond with the fibers and increase the strength. Further, the metallic element with its anchors cemented into the grooves reinforces the board further so that the finished board is stronger than it was originally.
12” x 84” V series heater board supported in the center only.
With the V-series’ robust panel heater construction, there is no need for costly special handling.
The alloy used for stamped element heaters has an upper temperature limit of 2,370 oF. In conventional (pinned-element) construction however, the allowable temperature range is reduced by the poor hot-strength performance of their elements which are only intermittently supported by pins. Because the V series elements are securely anchored every 1/8” along their entire length, they are able to withstand higher element temperatures without sag or element bunching. In addition, the V shape makes the elements more rigid and controls the element’s thermal expansion and contraction so that the element will not distort even at extremely high temperatures. The exceptional hot strength extends the allowable temperature range for V series elements. The V series is available at watt densities up to 100WSI, a level that was previously unachievable by any medium wavelength panel heater.
To illustrate the exceptional hot strength of the V-Series elements, the heaters were subjected to a torture test. The voltage was adjusted so that both heaters operated at an element surface load of 75 watts per square inch. This resulted in the competitor’s heater running at 2,040W and the V-Series heater running at 2,119W. The heaters were operated face-down and cycled on and off for 2.5 minute intervals. The test ran 24 hours a day for a period of two weeks.
The before and after photos show that the V series heater looks like new, whereas the competitor’s has suffered a tremendous amount of element sag and creep. It simply cannot stand up to the element temperatures and wattage loading that the V series can. It should be noted that pinning every single loop would not be a good solution for conventional construction. Although this would diminish element sagging, it would significantly increase the cost, significantly weaken the board, significantly increase back losses and create new thermal expansion issues.
After high temperature testing, the V series heater retains its original uniformity while the competitor has portions of elements hanging closer to the product than others. With difficult-to-process materials, this may result in non-uniform heating. The distorted element will fail more quickly as a result of element loops moving closer together and creating hot spots.
Pinned to refractory board
Individual elements are potentially replaceable (provided board is not cracked or broken)
Permanently bonded to refractory board
Less Expensive: laborious manual insertion and folding over of pins is eliminated, thus resulting in a more economical heater.
More efficient:
thermally conductive heat-robbing pins are eliminated
2” of TIW insulation behind the refractory board reduces back-side heat loss and improves transfer of heat to the product.
Robust construction: Refractory board is not perforated by numerous pins which makes our board much stronger. Refractory board does not develop cracks at high temperature.
No special handling: Equipment can be shipped with heaters installed. Save money by not removing, packing and then re-installing on site.
High power capability: The highest power capability of any medium wavelength panel heater in the world. Save money by installing fewer heaters.
Longer life: More freely radiating elements, plus secure anchoring, plus controlled thermal expansion/ contraction, plus elimination of element sag/creep all add up to longer life.
Find more
© 2021 CMT EAST ASIA CO. All rights reserved 粤ICP备 18018792
